Stainless steel woven mesh for filter support
Woven wire cloth for inner and outer support layers, guards and drainage layers where epoxy or zinc is not acceptable: aggressive fluids, phosphate-ester hydraulics, steam and hot gas, and hygienic service. Plain weave for most support layers, twill weave for heavier wire at the same mesh count, and Dutch weave where the support itself must carry a high pressure load.

Plain weave support and guard meshes
Mesh count, open area and weight are theoretical values for plain-weave stainless steel cloth; multiply weight by the density ratio for other alloys. Grade: Market = general-purpose standard; Mill = higher open area. Other combinations on request.
| Code | Mesh per in | Wire mm | Wire in | Opening mm | Open area % | Weight kg/m² | Grade |
|---|---|---|---|---|---|---|---|
| SS2500-710 | 8 | 0.710 | 0.0280 | 2.50 | 61 | 1.99 | Market |
| SS2000-500 | 10 | 0.500 | 0.0197 | 2.00 | 64 | 1.27 | Mill |
| SS1700-450 | 12 | 0.450 | 0.0177 | 1.70 | 63 | 1.20 | Mill |
| SS1400-450 | 14 | 0.450 | 0.0177 | 1.40 | 57 | 1.39 | Mill |
| SS1180-400 | 16 | 0.400 | 0.0157 | 1.18 | 56 | 1.29 | Mill |
| SS1000-400 | 18 | 0.400 | 0.0157 | 1.00 | 51 | 1.45 | - |
| SS850-400 | 20 | 0.400 | 0.0157 | 0.850 | 46 | 1.63 | Market |
| SS710-355 | 24 | 0.355 | 0.0140 | 0.710 | 44 | 1.50 | Market |
| SS541-305 | 30 | 0.305 | 0.0120 | 0.541 | 41 | 1.39 | Market |
| SS450-280 | 35 | 0.280 | 0.0110 | 0.450 | 38 | 1.36 | Market |
| SS381 | 40 | 0.254 | 0.0100 | 0.381 | 36 | 1.29 | Market |
| SS280-224 | 50 | 0.224 | 0.0088 | 0.280 | 31 | 1.26 | Market |
| SS236-190 | 60 | 0.190 | 0.0075 | 0.236 | 31 | 1.08 | Market |
| SS180-140 | 80 | 0.140 | 0.0055 | 0.180 | 32 | 0.78 | Market |
Plain Dutch weave
Dutch weaves pack the weft wires tightly against a heavy warp. There is no straight-through opening, so the cloth combines a fine pore with very high mechanical strength. As a support or backing layer it carries high differential pressure behind finer filter media.
| Code | Geometric pore µm | Nominal rating µm | Mesh per in (warp x weft) | Wire mm (warp x weft) | Weight kg/m² |
|---|---|---|---|---|---|
| SS301-PD | 301 | 250 | 12 x 64 | 0.580 x 0.400 | 3.64 |
| SS256-PD | 256 | 250 | 14 x 88 | 0.500 x 0.330 | 3.15 |
| SS162-PD | 162 | 120 | 20 x 150 | 0.248 x 0.177 | 1.48 |
| SS153-PD | 153 | 110 | 24 x 110 | 0.355 x 0.250 | 2.70 |
| SS120-PD | 120 | 90 | 30 x 150 | 0.230 x 0.180 | 1.60 |
| SS91-PD | 91 | 70 | 40 x 200 | 0.180 x 0.140 | 1.30 |
| SS72-PD | 72 | 55 | 50 x 250 | 0.140 x 0.114 | 1.00 |
| SS45-PD-B | 45 | 40 | 80 x 400 | 0.125 x 0.071 | 0.81 |
Twill Dutch weave
| Code | Geometric pore µm | Nominal rating µm | Mesh per in (warp x weft) | Wire mm (warp x weft) | Weight kg/m² |
|---|---|---|---|---|---|
| SS134-TD | ≈134 | ≈100 | 24 x 220 | 0.300 x 0.250 | 3.98 |
| SS121-TD | 121 | ≈90 | 30 x 360 | 0.250 x 0.150 | 2.49 |
| SS88-TD | 88 | ≈65 | 40 x 560 | 0.180 x 0.100 | 1.72 |
| SS46-TD | 46 | 35 | 80 x 700 | 0.100 x 0.080 | 1.32 |
Geometric pore calculated from the mesh geometry (ASTM E2814); comparable to an absolute rating. Nominal rating = typical retention in service. ≈ = calculated value, nominal estimated; glass bead test on request. Weights for stainless steel.
Plain or Dutch as the support layer?
Plain or twill weave
Use where the support only has to hold the media and pass flow freely: inner and outer support of liquid cartridges, guards and drainage layers.
Dutch weave
Use where the support must carry a high pressure load, or where it doubles as a protective pre-filter behind the main media.
Materials and supply
| Item | Specification |
|---|---|
| Materials | AISI 304, 304L, 316, 316L standard; 310S, nickel alloys and other grades woven to order |
| Supply | Rolls, slit rolls, cut pieces and discs; pleated or formed parts to drawing on request |
| Alloy identification | Wire and finished cloth checked by handheld XRF before weaving and before shipment |
| Certificates | EN 10204 3.1 mill certificate per heat, available with every order |
Full data in the catalogue. Specifications, tolerances, materials and inspection for all six support media are in the MAISHI Filter Support Mesh Catalogue (PDF, 32 pages, 1.7 MB).
Related support media
Need a different mesh, alloy or a Dutch weave rating?
Send the fluid, temperature, pressure and the mesh you use today. We recommend a cloth and quote rolls or cut pieces.
Frequently asked questions
When should I use stainless woven cloth instead of epoxy coated screen?
Where epoxy or zinc is not acceptable: phosphate-ester hydraulic fluids, aggressive process fluids, steam and hot gas above about 120 °C, and hygienic service. Stainless 304 and 316 are rated to about 925 °C in clean, dry air.
What is the difference between plain weave and Dutch weave as a support layer?
Plain or twill weave holds the media and passes flow freely. Dutch weave packs fine weft wires against a heavy warp, has no straight-through opening and carries a much higher pressure load, so it is used behind finer media in high-pressure liquid and polymer filters.
What do geometric pore and nominal rating mean for Dutch weave?
Geometric pore is the diameter of the largest sphere that passes the pore, calculated from the mesh geometry to ASTM E2814; it is comparable to an absolute rating. Nominal rating is the typical retention in service and is always smaller. Confirmation by glass bead test is available on request.
Which alloys are available?
AISI 304, 304L, 316 and 316L are standard. Heat-resistant 310S and nickel alloys are woven to order. Wire and finished cloth are checked by handheld XRF to confirm the alloy grade.