Menu
ProductsExpanded MetalEpoxy Coated ScreenWelded MeshMembrane Support MeshStainless Woven MeshPP Support MeshApplicationsAll ApplicationsPleated Air FiltersDust Collector CartridgesHydraulic & Liquid FiltersBag & Panel Filter BackingTechnicalSelection GuideTechnical GuideMaterial GuideGBW vs GAW Welded MeshEpoxy Mesh Wire DiameterProduct Catalogue (PDF)AboutAbout MAISHIQuality & InspectionMAISHI Main SiteContact
Technical · Material selection

Material guide for filter support mesh

Choose the material for the fluid, the temperature and the cleaning regime; then choose the construction for the load. Ratings are for general guidance at moderate concentration and temperature.

Stainless steels and nickel alloys

Material (EN / UNS)Max. service in air*Oxidizing acidsReducing acidsAlkalisChloridesTensile Rm MPa**Typical use
304 (1.4301 / S30400)925 °CGoodLimitedVery goodLimited≥ 515General liquid filters, washable filters, food
316L (1.4404 / S31603)925 °CGoodModerateVery goodModerate≥ 485Chlorides, marine air, chemical and hygienic service
310S (1.4845 / S31008)1,150 °CGoodLimitedVery goodLimited≥ 515Hot gas, furnace and kiln filtration
Inconel® 600 (2.4816 / N06600)1,175 °CModerateModerateExcellentGood≥ 550Hot caustic, high-temperature oxidizing gas
Inconel® 625 (2.4856 / N06625)980 °CVery goodVery goodVery goodExcellent≥ 827Seawater, sour and chloride service
Hastelloy® C-276 (2.4819 / N10276)1,040 °CVery goodExcellentVery goodExcellent≥ 690Strong reducing acids, wet chlorine, mixed chemicals
Titanium Gr 2 (3.7035 / R50400)425 °CExcellentPoorGoodExcellent≥ 345Seawater, chlorides, oxidizing acids

Coated steels, aluminium and polymers

MaterialMax. service*Service notesUsed in
Low-carbon steel + epoxyAbout 120 °C (coating)Mineral oils, lube oils, diesel; not phosphate-ester fluidsEpoxy coated screen
Galvanized steel (strip to EN 10346)About 200 °C (zinc)Indoor and outdoor air, humid intake air; poor in acids and alkalisExpanded metal, welded mesh
Aluminium 5154A / 5056AAbout 120 °C (epoxy)Lightweight engine and HVAC filtersEpoxy coated screen, expanded metal
Polyester (PET)150 °CGood in acids, limited in alkalisMembrane support mesh
Nylon (PA6 / PA66)100-115 °CGood in alkalis, limited in acidsMembrane support mesh
Polypropylene (PP)See product pageHumid, acidic or incinerable filtersPP support mesh

* Typical maximum continuous service temperature in clean, dry air for the metal or, where stated, for its coating. Actual limits depend on load, atmosphere and duty cycle. Aluminium-magnesium alloys with more than 3 % Mg are not recommended for sustained service above about 65 °C in corrosive environments. ** Minimum tensile strength, annealed condition, as specified in ASTM A580 (stainless wire), ASTM B166, B446 and B574 (nickel alloys) and ASTM B348 (titanium); galvanized strip to EN 10346 DX51D: 270-500 MPa. The actual value of each heat is stated on the EN 10204 3.1 mill certificate. Inconel® is a trademark of Special Metals Corporation; Hastelloy® is a trademark of Haynes International.

Quick selection

Hydraulic fluids

Mineral oils: epoxy coated steel screen. Phosphate-ester fluids: stainless 316L woven mesh.

Humid or coastal air

Welded mesh hot-dip galvanized after welding (GAW), or stainless 316L for the longest life.

Above 450 °C

310S or nickel alloys. Above 925 °C, nickel alloys only.

Food and pharma

316L woven cloth; PET or PA6 monofilament with FDA test reports.

Full data in the catalogue. Specifications, tolerances, materials and inspection for all six support media are in the MAISHI Filter Support Mesh Catalogue (PDF, 32 pages, 1.7 MB).

Not sure which material fits your service?
Send the fluid, temperature, pressure and cleaning regime. We recommend a material and construction.

Get A Quote

Frequently asked questions

Which support mesh material for phosphate-ester hydraulic fluid?

Stainless steel 316L. Epoxy coated screen has good resistance to mineral hydraulic oils, lube oils and diesel but is not recommended for phosphate-ester fluids.

What is the maximum temperature for galvanized and epoxy coated support mesh?

About 200 °C for zinc coatings and about 120 °C for continuous service of epoxy coated mesh. Above 450 °C use 310S or nickel alloys; above 925 °C, nickel alloys only.

Where do the tensile strength values come from?

They are minimum tensile strengths in the annealed condition as specified in the ASTM product standards (stainless wire ASTM A580; nickel alloys ASTM B166, B446 and B574; titanium ASTM B348) and EN 10346 for DX51D galvanized strip. The actual value of each heat is stated on the EN 10204 3.1 mill certificate.